Toyota CH-R: Meter display

The units of measure may differ depending on the intended destination of the vehicle.

1. Engine coolant temperature gauge Displays the engine coolant temperature.
2. Outside temperature
3. Analog meter

The dial type of analog meter can be changed on of the multi-information display.

Tachometer: Displays the engine speed in revolutions per minute.

Hybrid System Indicator: Displays the Hybrid System Indicator.

4. Shift position indicator
5. Speedometer

Displays the vehicle speed.

6. Clock

Automatically adjusts the time by using the GPS time information (GPS clock).

For details, refer to "Multimedia owner's manual".

7. Fuel gauge

Displays the quantity of fuel remaining in the tank.

In the following situations, the actual quantity of fuel remaining in the tank may not be displayed correctly. Refer to P.102 if the actual quantity of fuel remaining in the tank is not displayed correctly.

• A small amount of fuel is added.
• Fuel is added with the fuel gauge near or at "1/1".
• The vehicle is stopped on an uneven surface, such as a slope.
• The vehicle is driven on a slope or around a curve.

8. Distance to empty

Displays driving range with remaining fuel.

9. Multi-information display

Presents the driver with a variety of vehicle data. Displays warning messages if a malfunction occurs.

10. Odometer and distance until next engine oil change display

Odometer: Displays the total distance the vehicle has been driven.

Distance until next engine oil change: Displays the distance the vehicle can be driven until an oil change is necessary.

The distance until the next engine oil change will also be displayed in the following situations:

• When the power switch is turned to ON.
• When a warning message indicating that oil maintenance should be performed soon or is required is displayed.
• Resetting

■The meters and display illuminate when

The power switch is in ON.

■When the drive mode is changed

Background color is changed following the selected driving mode.

■Engine speed

On hybrid electric vehicles, engine speed is precisely controlled in order to help improve fuel efficiency and reduce exhaust emissions, etc.

There are times when the engine speed that is displayed may differ even when vehicle operation and driving conditions are the same.

■If the units of measure for speedometer can be changed

The other units of measure is also displayed as shown in the illustrations.

■Hybrid System Indicator

1. Charge area

Shows regeneration* status.

Regenerated energy will be used to charge the hybrid battery (traction battery).

2. Eco area

Shows that the vehicle is being driven in an Eco-friendly manner.

By keeping the indicator needle within Eco area, more Eco-friendly driving can be achieved.

3. Power area

Shows that an Eco-friendly driving range is being exceeded (during full power driving, etc.)

4. Hybrid Eco area

Shows that gasoline engine power is not being used very often.

The gasoline engine will automatically stop and restart under various conditions.

*: When used in this manual, "regeneration" refers to the conversion of energy created by the movement of the vehicle into electrical energy.

In the following situation, the Hybrid System Indicator does not operate.

• "READY" indicator is not illuminated.
• The shift position is in a range other than D or B.

■Outside temperature display

• Displays the outside temperature within the range of -40ºC (-40ºF) to 60ºC (140ºF).
• When the outside temperature is approximately 3ºC (37ºF) or lower, the indicator will flash for approximately 10 seconds, then stay on.
• In the following situations, the correct outside temperature may not be displayed, or the display may take longer than normal to change:
  • When stopped, or driving at low speeds (less than 25 km/h [16 mph] )
  • When the outside temperature has changed suddenly (at the entrance/exit of a garage, tunnel, etc.)
• When "--" or "E" is displayed, the system may be malfunctioning. Take your vehicle to any authorized Toyota retailer or Toyota authorized repairer, or any reliable repairer.

■Fuel gauge and driving range display

The fuel gauge and driving range display are linked. If the fuel gauge and driving range display do not update after refueling a small amount, they can be updated by performing the following procedure:

1. Stop the vehicle on a level surface.

Wait until the fuel in the fuel tank stabilizes.

2. Turn the power switch off.

3. While pressing and holding of the meter control switch, turn the power switch to ON.

4. Continue holding of the meter control switch for approximately 5 seconds.

Release the button when the odometer begins blinking.

Updating will be complete when the odometer blinks for approximately 5 seconds and then returns to the normal display.

■Distance to empty

• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
• When only a small amount of fuel is added to the tank, the display may not be updated. When refueling, turn the power switch off. If the vehicle is refueled without turning the power switch off, the display may not be updated.
• When "Refuel" is displayed, the remaining fuel amount is low and the distance that can be driven with the remaining fuel cannot be calculated.

  Refuel immediately.

■Free/Open Source Software Information

This product contains Free/Open Source Software (FOSS). The license information and/or the source code of such FOSS can be found at the following URL.

https://www.denso.com/global/en/ opensource/meter/toyota/

■Customization

The gauges and meters can be customized in of the multi-information display.

WARNING

■The information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

NOTICE

■To prevent damage to the engine and its components

• Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed.
• The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely.